EEPROM(8) OpenBSD System Manager's Manual EEPROM(8)NAMEeeprom - display or modify contents of the EEPROM or OpenPROM
SYNOPSISeeprom [-cipv] [-f device] [-N system] [field[=value] ...]
DESCRIPTIONeeprom provides an interface for displaying and changing the contents of
the EEPROM or OpenPROM. Without any arguments, eeprom will list all of
the known fields and their corresponding values. When given the name of
a specific field, eeprom will display that value or set it if the field
name is followed by `=' and a value. Only the superuser may modify the
contents of the EEPROM or OpenPROM.
The options are as follows:
- Commands are taken from stdin and displayed on stdout.
-ceeprom will fix incorrect checksum values and exit. This flag is
quietly ignored on systems with an OpenPROM.
-f device
On systems with an EEPROM, use device instead of the default
/dev/eeprom. On systems with an OpenPROM, use device instead of
the default /dev/openprom.
-i If checksum values are incorrect, eeprom will ignore them and
continue after displaying a warning. This flag is quietly
ignored on systems with an OpenPROM.
-N system
Use the system image system instead of the default /bsd.
-p On systems with an OpenPROM, display the tree derivated from it
and exit. This flag is quietly ignored on systems with an
EEPROM.
-v On systems with an OpenPROM, be verbose when setting a value.
Systems with an EEPROM are always verbose.
FIELDS AND VALUES
The following fields and values are for systems with an EEPROM:
hwupdate A valid date, such as ``7/12/95''. The strings
``today'' and ``now'' are also acceptable.
memsize How much memory, in megabytes, is installed in the
system.
memtest How much memory, in megabytes, is to be tested upon
power-up.
scrsize The size of the screen. Acceptable values are
``1024x1024'', ``1152x900'', ``1600x1280'', and
``1440x1440''.
watchdog_reboot If true, the system will reboot upon reset.
Otherwise, the system will fall into the monitor.
default_boot If true, the system will use the boot device stored in
bootdev.
bootdev Specifies the default boot device in the form
cc(x,x,x), where ``cc'' is a combination of two
letters such as ``sd'' or ``le'' and each ``x'' is a
hexadecimal number between 0 and ff, less the
prepending ``0x''.
kbdtype This value is ``0'' for all Sun keyboards.
console Specifies the console type. Valid values are ``b&w'',
``ttya'', ``ttyb'', ``color'', and ``p4opt''.
keyclick If true, the keys click annoyingly.
diagdev This is a string very similar to that used by bootdev.
It specifies the default boot device when the
diagnostic switch is turned on.
diagpath A 40-character, NULL-terminated string specifying the
kernel or stand-alone program to load when the
diagnostic switch is turned on.
columns An 8-bit integer specifying the number of columns on
the console.
rows An 8-bit integer specifying the number of rows on the
console.
ttya_use_baud Use the baud rate stored in ttya_baud instead of the
default 9600.
ttya_baud A 16-bit integer specifying the baud rate to use on
ttya.
ttya_no_rtsdtr If true, disables RTS/DTR.
ttyb_use_baud Similar to ttya_use_baud, but for ttyb.
ttyb_baud Similar to ttya_baud, but for ttyb.
ttyb_no_rtsdtr Similar to ttya_no_rtsdtr, but for ttyb.
banner An 80-character, NULL-terminated string to use at
power-up instead of the default Sun banner.
Note that the secure, bad_login, and password fields are not currently
supported.
Since the OpenPROM is designed such that the field names are arbitrary,
explaining them here is dubious. Below are field names and values that
one is likely to see on a system with an OpenPROM. NOTE: this list may
be incomplete or incorrect due to differences between revisions of the
OpenPROM.
sunmon-compat? If true, the old EEPROM-style interface will be
used while in the monitor, rather than the
OpenPROM-style interface.
selftest-#megs A 32-bit integer specifying the number of
megabytes of memory to test upon power-up.
oem-logo A 64bitx64bit bitmap in Sun Iconedit format. To
set the bitmap, give the pathname of the file
containing the image. NOTE: this property is not
yet supported.
oem-logo? If true, enables the use of the bitmap stored in
oem-logo rather than the default Sun logo.
oem-banner A string to use at power-up, rather than the
default Sun banner.
oem-banner? If true, enables the use of the banner stored in
oem-banner rather than the default Sun banner.
ttya-mode A string of five comma separated fields in the
format ``9600,8,n,1,-''. The first field is the
baud rate. The second field is the number of
data bits. The third field is the parity;
acceptable values for parity are ``n'' (none),
``e'' (even), ``o'' (odd), ``m'' (mark), and
``s'' (space). The fourth field is the number of
stop bits. The fifth field is the ``handshake''
field; acceptable values are ``-'' (none), ``h''
(RTS/CTS), and ``s'' (XON/XOFF).
ttya-rts-dtr-off If true, the system will ignore RTS/DTR.
ttya-ignore-cd If true, the system will ignore carrier detect.
ttyb-mode Similar to ttya-mode, but for ttyb.
ttyb-rts-dtr-off Similar to ttya-rts-dtr-off, but for ttyb.
ttyb-ignore-cd Similar to ttya-ignore-cd, but for ttyb.
sbus-probe-list Four digits in the format ``0123'' specifying
which order to probe the SBus at power-up. It is
unlikely that this value should ever be changed.
screen-#columns An 8-bit integer specifying the number of columns
on the console.
screen-#rows An 8-bit integer specifying the number of rows on
the console.
auto-boot? If true, the system will boot automatically at
power-up.
watchdog-reboot? If true, the system will reboot upon reset.
Otherwise, the system will fall into the monitor.
input-device One of the strings ``keyboard'', ``ttya'', or
``ttyb'' specifying the default console input
device.
output-device One of the strings ``screen'', ``ttya'', or
``ttyb'' specifying the default console output
device.
keyboard-click? If true, the keys click annoyingly.
sd-targets A string in the format ``31204567'' describing
the translation of physical to logical target.
st-targets Similar to sd-targets, but for tapes. The
default translation is ``45670123''.
scsi-initiator-id The SCSI ID of the on-board SCSI controller.
hardware-revision A 7-character string describing a date, such as
``25May95''.
last-hardware-update Similar to hardware-revision, describing when the
CPU was last updated.
diag-switch? If true, the system will boot and run in
diagnostic mode.
local-mac-address? When set to false, all Ethernet devices will use
the same system default MAC address. When true,
Ethernet devices which have a unique MAC address
will use it rather than the system default MAC
address. This option only really affects FCode-
based Ethernet devices. In reality, this means
that on Sparc machines with an OpenPROM, only
hme(4) Ethernet devices respect this setting. On
Sparc64, all on-board devices, as well as plug-in
hme(4) boards, will respect this setting; other
hardware will not.
FILES
/dev/eeprom the EEPROM device on systems with an EEPROM
/dev/openprom the OpenPROM device on systems with an OpenPROM
SEE ALSOopenprom(4)CAVEATS
The fields and their values are not necessarily well defined on systems
with an OpenPROM. Your mileage may vary.
There are a few fields known to exist in some revisions of the EEPROM
and/or OpenPROM that are not yet supported. Most notable are those
relating to password protection of the EEPROM or OpenPROM.
Avoid gratuitously changing the contents of the EEPROM. It has a limited
number of write cycles.
The date parser isn't very intelligent.
OpenBSD 4.9 June 26, 2008 OpenBSD 4.9